新葡亰8883ent登陆|(集团)有限公司

新葡亰8883ent登陆-(集团)有限公司

全国热线电话:

17116125111

热门搜索: (集团)有限公司石磨机 (集团)有限公司 (集团)有限公司石磨机 (集团)有限公司
联系大家
    新葡亰8883ent登陆-(集团)有限公司
  • 联系:和经理
  • 电话:17116125111
  • 手机:17116125111
  • 邮箱:3471464452@qq.com
  • 网址:
  • 厂址:山东省济南市章丘区相公庄镇
资讯资讯 您现在的位置:新葡亰8883ent登陆 - 资讯资讯 >

怎样正确安装新葡亰8883ent登陆?

来源:/发布时间:2022-03-17

新葡亰8883ent登陆从订购到安装直至顺利运营,其中重要环节为面粉机的安装。 From ordering to installation to smooth operation of flou

新葡亰8883ent登陆从订购到安装直至顺利运营,其中重要环节为面粉机的安装。
From ordering to installation to smooth operation of flour machine, the important link is the installation of flour machine.
面粉机在发货时多数为零散装货,这就意味着,面粉机的组装、试机都要谨慎进行。尤其是一台全自动面粉机,面粉机安装正确与否,关乎着机器的使用效率和产品质量。所以,如何正确安装面粉机,显得尤为重要。下面面粉机厂家先容面粉机正确安装步骤。
Most of the flour machines are loaded sporadically during delivery, which means that the assembly and test run of the flour machine should be carried out carefully. Especially for a full-automatic flour machine, whether the flour machine is installed correctly or not is related to the use efficiency and product quality of the machine. Therefore, how to correctly install the flour machine is particularly important. Next, the flour mill manufacturer introduces the correct installation steps of the flour mill.
怎样正确安装新葡亰8883ent登陆?全自动面粉机安装分为安装与安装后的调试两大部分。
How to install flour stone mill correctly? The installation and commissioning of most automatic flour machines are divided into two parts.
1、安装
1. Installation
磨面机的磨头应安装端正。用M16的螺栓固定在混凝土基础上,电动经营可靠接地,以防漏电,所有电器应有电工安装。
The grinding head of the grinding machine shall be installed correctly. Fixed on the concrete foundation with M16 bolts, the electric operation shall be reliably grounded to prevent electric leakage, and all electrical appliances shall be installed by electricians.
用户应根据磨面机配套的需要,自行配备主动力电机1台及其他电器设备和线路。
Users should provide one set of main power motor and other electrical equipment and circuits according to the needs of the grinder.
磨面机的安装必须在厂方技术人员的引导下进行,安装后的调整、试车、由厂方技术人员操作。
The installation of the grinder must be carried out under the guidance of the manufacturer's technicians, and the adjustment, commissioning and operation after installation shall be operated by the manufacturer's technicians.
▲注意:电源应连接可靠,电机有接地线,工作位置至电器控制开关位置,方便于及时切断电源,防护罩要固定牢靠。
▲ note: the power supply should be connected reliably. The motor has a grounding wire. The working position is to the position of the electrical control switch, which is convenient to cut off the power supply in time. The protective cover should be fixed firmly.
▲警告:一定要安装好防护罩,防止伤人,按要求的位置贴好警示标志。
▲ warning: the protective cover must be installed to prevent personal injury, and warning signs shall be pasted at the required position.
2、面粉机安装后的调试
2. Commissioning of flour mill after installation
新出厂磨面机安装后都要进行调试方可试车,开机前应仔细检查传动皮带及防护装置,检查各部分紧固件是否松动,检查轴承、齿轮松紧是否合适,检查粮仓、磨内是否有异物,用手转动磨机大皮带轮,检查颤动是否正常。
After the new mill is installed, it must be debugged before commissioning. Before starting up, carefully check the transmission belt and protective device, check whether the fasteners of each part are loose, whether the tightness of bearings and gears is appropriate, check whether there are foreign matters in the granary and mill, rotate the large belt pulley of the mill by hand and check whether the vibration is normal.
启动电动机:启动电动机检查转向是否正确,转动是否正常,发现异常,马上停机检修。
Start the motor: start the motor to check whether the rotation direction is correct and whether the rotation is normal. If any abnormality is found, stop the machine for maintenance immediately.
新面粉机安装调试后,应先用麸皮试磨不少于30分钟,将磨机内清理干净后,再开始正常加工小麦面粉。
After the installation and commissioning of the new flour mill, try grinding with bran for no less than 30 minutes, clean the mill, and then start the normal processing of wheat flour.
根据物料颗粒调整流量调节小手柄,使每一遍加工的流量合适。
Adjust the flow according to the material particles, and adjust the small handle to make the flow of each processing appropriate.
工作时先启动风机,待风机运转正常后再启动磨粉机,开动主机时磨辊处在断开位置,待下料正常后方可磨合磨辊。
When working, start the fan first, and then start the pulverizer after the fan operates normally. When starting the main engine, the grinding roller is in the disconnected position, and the grinding roller can be run in after the blanking is normal.
操作注意事项:
Precautions for operation:
▲严禁将金属块、石块、铁钉等混入磨中。
▲ it is forbidden to mix metal blocks, stones, nails, etc. into the mill.
▲严禁将磨辊在未喂入物料的情况下推向磨合状态。
▲ it is forbidden to push the grinding roller to the running in state without feeding materials.
相关资讯
相关产品
新葡亰8883ent登陆 走进中阳 产品中心 石磨小吃 资讯资讯 联系大家 网站地图 XML TXT
新葡亰8883ent登陆-(集团)有限公司技术支撑:网站建设-推广运营

新葡亰8883ent登陆|(集团)有限公司

XML 地图 | Sitemap 地图